Funmit Wall Fitting Replacement for Polaris 180/280 Pool Cleaners — Universal 1-1/2in Thread Bayonet Collar

The Funmit 6-500-00 universal wall fitting is a direct replacement collar that restores a secure, leak-free connection between your Polaris automatic pool cleaner and the pool wall.

If the wall fixture on your Polaris-style cleaner has cracked, swollen, or started leaking, this 6-500-00 replacement part provides a durable, direct-fit repair. Designed as a universal wall fitting (UWF) for many Polaris models, the Funmit collar reconnects the bayonet-style cleaner hose to the skimmer or dedicated wall inlet so your cleaner can regain full suction and reliable operation.

Which Polaris and similar models does this wall fitting fit?

The Funmit 6-500-00 is compatible with a wide range of Polaris and Polaris-style vacuums and tank-trax models. It replaces worn or broken wall fixtures and is listed as an equivalent for several part numbers and model families.

• Compatible with Polaris 65 Turbo Turtle, 360, 380 series, and 280/180 Vac Sweep units.
• Also suitable for models labeled 3900 Sport, 380 Vac Sweep, 360 Vac Sweep.
• Fits 280 TankTrax, 180 Vac Sweep, 165 Vac Turbo Sweep and other bayonet-style cleaners.
• Universal collar design for many standard bayonet inlet fittings used on legacy Polaris systems.

How does installation work and what tools are needed?

Installation is straightforward for homeowners familiar with pool fittings. One side of the connector screws into a 1-1/2" threaded wall inlet while the opposite side accepts the cleaner's bayonet tabs, locking in place for a secure connection.

• Thread size: 1-1/2" pool wall thread on the inlet side for standard plumbing attachments.
• Bayonet side provides two nubs that engage the cleaner hose bayonet for a positive lock.
• Basic tools: channel pliers or strap wrench for removal/installation of old fittings; plumber's lubricant or Teflon tape optional for threads.
• Typical install time: under 15 minutes for most DIYers with simple hand tools.

What performance and durability can I expect from this adapter?

The 6-500-00 is manufactured as a wear-resistant collar to hold the bayonet fitting firmly against the pool wall connector. It restores performance by eliminating leaks and wobble that reduce suction and cleaner efficiency.

• Durable construction resists swelling and cracking common in old or sun-damaged fittings.
• Precise fit reduces water leakage, improving vacuum consistency and run time.
• Corrosion-resistant materials suitable for typical pool chemical exposure.
• Designed to match bayonet geometry of Polaris-style hoses for reliable locking action.

What should I check if it still leaks after replacement?

Occasional leaks after replacing a wall fitting often come from improper thread seating, damaged threads on the pool inlet, or worn bayonet tabs on the cleaner hose. Troubleshooting a few simple points usually resolves these issues without further parts.

• Confirm 1-1/2" threads are clean and free of debris before installing the new collar.
• Use a light wrap of Teflon tape on the wall inlet threads if small seam leaks appear.
• Inspect cleaner hose bayonet tabs for wear; replace hose end if tabs are rounded or broken.
• Hand-tighten then secure with a strap wrench—avoid excessive torque that can crack the new fitting.

Who is this for: The Funmit 6-500-00 wall fitting is aimed at pool owners and maintenance technicians with older Polaris or Polaris-style automatic cleaners who need a reliable, affordable repair part. If your cleaner wobbles at the wall, loses suction, or the original inlet has swollen or cracked, this universal collar offers a straightforward replacement to restore normal cleaning performance without replacing the entire cleaner or plumbing system.